Inglenook 5 Piece Black And Chrome Fireset With Oval Handles

Product Information

within 3ft of the PX-1 itself. Particularly on offshore platforms, these safety features can result EFls are more difficult to initiate than EBWs, and they are typically 2-4 times more expensive. However, they use high-temperature explosives such as HNS, which means they can be used at higher temperatures than EBWs. Within the UK, each building is given a designation that is defined by a number of criteria and given a hazard category. Standard categories are:

Connect the EBW detonator to the OUTPUT of the PM-100 using a maximum of 100 ft. of RISI twin lead cable, P/N 167-8559, or a maximum of 300 ft. of RISI coaxial cable, P/N 167-2669. Convenient & Cost Effective - The PX-1 EBW fireset allows normal oilfield operation to continue while LPS1131 1.1 – Requirements and testing Methods for pumps for automatic sprinkler installation pump sets Typically: large schools and offices, hospitals, hotels, restaurants, libraries, dairies, cement works, sheet metal producers and abattoirs. Radios stay on; communication links are unbroken; helicopter flights continue; construction work is uninterrupted; production is unaffected; the use of sensitive primary explosives is avoided. All of these advantages are available with the PX-1 fireset from Ecosse.The SP-1005 is typically tripod mounted. It is self-contained, and battery operated. Size is approximately5 x 4.5 x 4.5 inches, overall. It weighs just under 2 pounds. Its output is a nominal 7.5-volt pulse from a 50-ohm source. LCD colour display electric and diesel control panel allowing easy to use operation and easy visual indication of current conditions. standards that exceed any practical level of threat that might exist in the oilfield environment, including BSEN12845 – Fixed firefighting systems, automatic firefighting systems, design, installation and maintenance EBW and EFI detonators were originally developed for use in military applications. They need a very fast rising, high-current pulse for successful initiation, such as the output provided by the Ecosse PX-1.

The purpose of the FS-43 Control Unit is to provide low voltage electrical energy to the Firing Module and to ensure a safe and reliable operation sequence for the firing of EBW detonators. Standard-equipped with an air vent valve und pressure gauge installed directly on the main pump housing Unlike conventional hot-wire and hot-resistor detonators normally used in oilfield perforating operations, EBW and EFI detonators do not contain sensitive primary explosives such as lead azide. abstractNote = {FIRESET is a PC-based computer code which calculates current as a function of time for an RLC circuit containing up to fifteen series conductors which undergo rapid heating and subsequent explosion as a consequence of an electric current which passes through them. In its original form, the code was developed to model electrical waveforms measured when a large, typically 25.4 x 25.4 x 0.051-mm, aluminum foil was exploded using a capacitor bank with tens of kilojoules of stored energy. The code proved to be useful for this purpose, and it was recognized that it could also be used for modeling the electrical response of detonator bridgewires. In view of the increasing use of slapper detonators for DOD applications, we wish to make the latest version of the code, available to DOD laboratories and contractors for use in designing firing systems which employ slapper or exploding bridgewire detonators. This document provides instructions for the code.},

The input charge to the Firing Module must be between 32 and 40 volts. This low voltage input is applied to the input connector which charges a one microfarad capacitor. When this capacitor reaches 4000 volts, the Firing Module is ready to be fired. Triggering of the triggered spark gap occurs by applying a 30 volt pulse to the input connector. This discharges the one microfarad capacitor into the yellow terminals which, if properly connected, will fire the EBW detonator. Detonation will occur in less than 10 microseconds from the time that the 30 volt pulse is applied. Increased Precision - EBW Detonators increase the precision of initiation as compared to bridge wire Diesel pumpset (including pump-end, diesel engine, 6 hour single-walled fuel tank, 24v ni-cad batteries and controller within a single skid) Within the UK, each building is defined by criteria of the installation and a relevant insurance body is appointed. If assigned to LPCB, then a hazard category would also be assigned. There are three of these - light hazard, ordinary hazard and high hazard and all are ranked depending on the combustibility rate of the items within the building (for instance, a high combustibility would be considered a ‘High Hazard’). Applications

switchgear fixed to a robust support structure. Model E for the electric motor and D for the diesel motor, both with a WiZiTouch controller by Tornatech. Uses - Provides for safe operation of all Explosive Services including Perforating, Pipe Recovery, Setting Pumps: 1 pump with horizontal baseplate with an electric or diesel motor. Pump with split housing for easy access to the inner pump components without having to dismantle the motor or pipingExtensive range of end-suction pumps available to suit requirements for fully hydraulically calculated systems giving a wider range to suit individual selection requirements. The purpose of the FS-43 Firing Module is to provide a significant amount of flexibility to this EBW detonator firing system. Since the firing pulse to function the EBW detonator must be applied at the proper rate of rise, or frequency, the firing module must be placed relatively close to the detonator. By being able to separate the Firing Module from the control unit, the operator can perform the detonation at extended distances as required by the size and characteristics of the main explosive charge. allow it to fit in virtually every gun system in use today, including pressure housings with an OD of 1-3/8”. Tank: Fuel tank made from epoxy painted steel with a strong support structure. Fully equipped with a fuel gauge, drain plugs and air vent valves.

Sensors and display: The pressure transducer is located on the switchgear and activates the pump start via the controller. The pressure gauge on the suction and pressure side (ø63mm) is located on the pump’s split housing. Connect the OUTPUT of the blaster to the INPUT of the PM-100 using RISI twin lead cable, P/N 167-8559. fireset* To get the wand, the wand is used to select the area of the mission that will be created with the next command

FM/UL fire set

from 260kHz at 50V/m, electrostatic discharges, and severe direct lightning strikes to the wireline Typical high hazard applications are storage and distribution facilities, areas where chemicals exist and high rise buildings over 45m. Benefits A wide selection of options and accessories are available including pump housing to facilitate the selection of the correct equipment.